QC/T 1058-2017: Download Full-PDF & Invoice in 9 seconds. Excerpt from above true-PDF:
QC/T 1058-2017
AUTOMOTIVE INDUSTRY STANDARD
OF THE PEOPLE’S REPUBLIC OF CHINA
ICS 43.040.60
T 26
Fingerprint recognition thief resistant automobile
equipment
ISSUED ON: JANUARY 09, 2017
IMPLEMENTED ON: JULY 01, 2017
Issued by: Ministry of Industry and Information Technology of PRC
Table of Contents
Announcement ... 3 
Foreword ... 9 
1 Scope ... 10 
2 Normative references ... 10 
3 Terms and definitions ... 11 
4 Principle ... 12 
5 General requirements ... 12 
6 Technical requirements ... 13 
7 Main technical parameters ... 15 
8 Test methods ... 18 
9 Inspection rules ... 23 
10 Marking, packaging, transportation, storage ... 24 
Annex:
References, names and dates of implementation of 42 automotive industry
standards
No. Standard reference Standard name
Standard
reference being
substituted
Date of
implementation
250 QC/T 776-2017 Motor caravan QC/T 776-2007 2017-07-01
251 QC/T 1051-2017 Coach car 2017-07-01
252 QC/T 1052-2017 Communication vehicle 2017-07-01
253 QC/T 1053-2017 Concrete spraying vehicle 2017-07-01
254 QC/T 1054-2017 Tunnel cleaning vehicle 2017-07-01
255 QC/T 1055-2017 Drainage and rescue vehicle 2017-07-01
256 QC/T 218-2017
Technical
specifications for
steering column
upper combined
switch of automobile
QC/T 218-1996 2017-07-01
257 QC/T 1056-2017
Technical
requirements and test
methods for
automotive dual
clutch automatic
transmission
assembly
2017-07-01
258 QC/T 245-2017
Technical
specifications for
isolated plant of
compressed-natural-
gas (CNG)
automobile
QC/T 245-2002 2017-07-01
259 QC/T 247-2017
Technical
specifications for
isolated plant of
liquefied petroleum
gas
QC/T 247-2002 2017-07-01
260 QC/T 1057-2017 Car snow chains 2017-07-01
261 QC/T 1058-2017 Car fingerprint identification device 2017-07-01
273 QC/T 1060-2017
Automotive
hexagonal flower
flange bolts
2017-07-01
274 QC/T 1061-2017
Road transport
lightweight fuel tank
vehicle anti-overflow
system
2017-07-01
275 QC/T 1062-2017
Road transport
lightweight fuel tank
vehicle unloading
valve
2017-07-01
276 QC/T 1063-2017
Road transport
lightweight fuel tank
vehicle oil and gas
recovery components
2017-07-01
277 QC/T 1064-2017
Road transport
flammable liquid
dangerous goods
tank vehicle -
breathing valve
2017-07-01
278 QC/T 1065-2017
Road transport
flammable liquid
dangerous goods
tank vehicle -
manhole cover
2017-07-01
279 QC/T 789-2017
Performance
requirements and
bench test methods
of automobile electric
vortex retarder
assembly
QC/T 789-2007 2017-07-01
280 QC/T 316-2017
Bench test methods
of fatigue strength for
automobile service
brake
QC/T 316-1999 2017-07-01
281 QC/T 201-2017
Nylon pipe joint size
for automobile air
brake
QC/T 201-1995 2017-07-01
282 QC/T 1066-2017
Performance
requirements of cable
assembly for vehicle
parking brakes and
bench test method
2017-07-01
Fingerprint recognition thief resistant automobile
equipment
1 Scope
This standard specifies the terms and definitions, principles, general
requirements, technical requirements, main technical parameters, test methods,
inspection rules, marking, packaging, transportation and storage of fingerprint
recognition thief resistant automobile equipment (hereinafter referred to as
"devices").
This standard applies to the fingerprint recognition thief resistant automobile
equipment.
2 Normative references
The following documents are essential to the application of this document. For
the dated documents, only the versions with the dates indicated are applicable
to this document; for the undated documents, only the latest version (including
all the amendments) are applicable to this standard.
GB/T 191 Packaging - Pictorial marking for handling of goods
GB 4208 Degrees of protection provided by enclosure (IP code)
GB/T 17619-1998 Limits and methods of testing for immunity of electrical /
electronic sub-assemblies in vehicles to electromagnetic radiation
GB/T 17626.2 Electromagnetic compatibility (EMC) - Testing and
measurement techniques - Electrostatic discharge immunity test
GB/T 17626.3 Electromagnetic compatibility - Testing and measurement
techniques - Radiated radio-frequency electromagnetic field immunity test
GB/T 19951 Road vehicles - Test methods for electrical disturbances from
electrostatic discharge
GB/T 21437.2-2008 Road vehicles - Electrical disturbances from conduction
and coupling - Part 2: Electrical transient conduction along supply lines only
QC/T 29106 Technical specification of low-voltage electric harness for motor
vehicles
Refusal rejection rate (FRR)
The proportion of the fingerprint images which are acquired respectively
from same finger and judged as the different fingers when performing 1:1
matching, expressed as a percentage.
3.7
One time watching rate [translator’s note: shall be one time matching
rate]
The proportion of the fingerprint images which are matched successfully and
enrolled at the first time of operation when judging the fingerprint images
which are acquired respectively from same finger as the same finger in the
course of performing 1:1 matching, expressed as a percentage.
3.8
False enrollment rate
The proportion of the fingerprints of the personnel who are rejected for
enrollment because the fingerprint images as acquired from the same finger
after processing cannot generate a template when extracting the fingerprint
features and cannot form the basis of matching, expressed as a percentage.
3.9
Miss work
The phenomena that the function of the device cannot be normally turned
on or off when it is disturbed by any external factors.
4 Principle
The fingerprint recognition thief resistant automobile equipment is mainly
composed of a host computer, a standalone module for fingerprint recognition,
an alarm device, a wire harness.
5 General requirements
5.1 The device shall have the function to prevent unauthorized users from
starting the engine or other major power source of the vehicle normally. The
drive power system of the vehicle cannot be started until the system is turned
on.
5.2 The size of the device or screen for acquiring the fingerprint image shall be
vehicle battery is replaced, the fingerprint information saved by the fingerprint
enrollment shall not be lost. Except for manual deletion or damage, fingerprint
information shall be permanently stored for a long time.
6.4.4 Management of usage rights.
The device shall have a hierarchical management function for user’s usage
rights. It shall have a corresponding authorization mechanism in the process of
fingerprint enrollment or deletion.
6.5 Basic functions of host
6.5.1 Vehicle start function.
It shall be able to set the automatic start or manual start of the vehicle engine.
The device shall have dual backup protection function. If one of the relays fails,
it will not affect the normal start and driving of vehicle.
6.5.2 System function.
When it is necessary to temporarily turn off the function of the device (such as
vehicle washing, repair, maintenance), the vehicle is brought to the state where
no device is installed to facilitate the repair, maintenance, etc. of the vehicle,
then the device is turned on after the vehicle is returned back to the user.
6.5.3 Password function
It shall be possible to set and use a password. When the fingerprint acquisition
function cannot achieve normal acquisition and comparison, the owner may use
the password function to start the vehicle engine normally.
6.5.4 Initialization function.
It shall be able to initialize the system to reach the exit-factory state.
6.5.5 Protection function.
The outer casing of the operating device for fingerprint acquisition shall be able
to withstand the IP50 degree of protection in GB 4208. When a little water is
spilled onto the outer casing of the operating device that collects the fingerprint,
there shall be no leakage.
6.6 Power supply
The power supply of the device adopts the DC battery power supply as provided
by the automobile DC generator as equipped by the vehicle.
7.21 Alarm function
7.21.1 When there are 3 consecutive fingerprint verification errors or 3
password input errors, the device shall be able to give an audible alarm or signal
output.
7.21.2 When the fingerprint recognition device for vehicle is disconnected or
short-circuited, the device shall be capable of giving an audible alarm or signal
output.
7.21.3 When the vehicle is started by abnormal means, the device shall be
capable of giving an audible alarm.
8 Test methods
8.1 Structure and appearance inspection
Use the testing, observation, measurement, and similar method to inspect the
structure and appearance of the fingerprint recognition thief resistant
automobile equipment.
8.2 Power test
8.2.1 Power supply inspection.
Use the DC-regulated power supply to replace the battery to connect the
fingerprint recognition thief resistant automobile equipment. Between the power
line as led from the positive pole of the power supply and the power line of the
device, connect the DC current meter in series, to carry out test in the working
state and standby state. The functions of the device shall be normal.
8.2.2 Undervoltage indication test.
Use the DC voltage-regulated power supply to supply power to the device. First
adjust the voltage-regulated power supply to the rated voltage. Carry out test
and the function shall be normal. Then reduce the power supply voltage to DC
9 V. At this time, the device shall be able to continuously and normally turned
on/off for 50 times.
8.2.3 Power supply adaptability test.
Continuously adjust the power supply to 9 V, 12 V, 15 V for cyclic test. Each test
time is not less than 10 min. Without any adjustments, the device shall be able
to meet the requirements of 7.10.
8.2.4 Overvoltage operation test.
position on the vehicle. Use the three directions X, Y, Z as specified in Table 3,
to carry out the sinusoidal vibration test in the range of 10 Hz ~ 55 Hz. If there
is a resonance point, vibrate it at this frequency for 30 min. If there is no
resonance point, vibrate it for 30 min at a frequency of 35 Hz, totally 90 min.
Check the appearance and functions of the system after the test.
8.4.3 Impact test.
Fix the device on the impact test bench according to the actual assembly
position on the vehicle. Follow the requirements of Table 3, impact it 3 times
along each direction of axis X, Y, Z. After the test, check the appearance and
each function of the system.
3.4.4 Free fall test.
Follow the requirements of Table 3 to carry out the free fall test. During the test,
it may be protected by the exit-factory packaging box. After the test, check each
function of the system.
8.5 Electromagnetic compatibility test
8.5.1 Test of electrostatic discharge immunity
The device shall be tested in accordance with the method specified in GB/T
17626.2. The test results shall meet the requirements of 7.16.1.
8.5.2 Test of radio frequency electromagnetic field radiation immunity.
The device shall be tested in accordance with the method specified in GB/T
17626.3. No malfunction shall occur during the test. The test results shall meet
the requirements of 7.16.2.
8.5.3 Test of electric fast transient pulse group immunity
The device shall be tested according to the transient immunity test
requirements and performance requirements of GB/T 21437.2-2008. The test
level and function level are as shown in Table 4. No malfunction shall occur
during the test. The test results shall meet the requirements of 7.16.3.
If the inspected item is qualified, it is judged that the batch of products is a
qualified product. If one or two items of the sample are judged as unqualified
items after inspection, it is necessary to double the sample from the batch of
products for re-inspection. If there are still unqualified items, the batch of
products is judged to be unqualified. If there are more than 2 unqualified items
in the sample after inspection, this batch of products are unqualified and shall
not be re-inspected.
9.5 Product quality certificate
The product quality certificate must state the relevant contents of 10.1 and 10.2
of this standard, the main contents of the instruction manual, precautions, after-
sales service commitment, maintenance contact address, telephone number,
etc.
10 Marking, packaging, transportation, storage
10.1 Marking
10.1.1 The product shall have clear and durable markings, including
nameplates or signs and quality inspection marking.
10.1.2 The nameplate or sign of the fingerprint recognition thief resistant
automobile equipment shall include the following contents:
a) Product name and model;
b) Product manufacturers and trademarks;
c) Exit-factory date and number of products;
d) Implemented standard number.
10.2 Packaging
10.2.1 The pictorial signs of packaging, storage, transportation shall comply
with the provisions of GB/T 191. The packaging box shall have a product quality
certificate, product instruction manual, certificate, after-sales service
registration card, insurance card, its attachment. When operated according to
the requirements of the product manual, it shall be able to correctly install, use
and maintain the fingerprint recognition thief resistant automobile equipment.
10.2.2 Select the packing box of appropriate specification according to the size
of the product. The packaging box shall have the name of the factory, the
address of the factory, the telephone number, the implemented product
standard number, the product model and name, the quantity, the exit-factory
date, the exit-factory inspection form of product, the protection requirements
......