标准搜索结果: 'GB/T 20564.10-2017英文版'
| 标准号码 | 内文 | 价格(元) | 第2步 | 交付天数[PDF] | 标准名称 | 相关标准 |
| GB/T 20564.10-2017 |
英文版
| 300 |
购买全文
|
现货, 9秒内下载
|
汽车用高强度冷连轧钢板及钢带 第10部分：孪晶诱导塑性钢
|
GBT 20564.10-2017
|
标准编号: GB/T 20564.10-2017 (GB/T20564.10-2017)
中文名称: 汽车用高强度冷连轧钢板及钢带 第10部分：孪晶诱导塑性钢
英文名称: Continuously cold rolled high strength steel sheet and strip for automobile -- Part 10: Twinning induced plasticity steel
行业: 国家标准 (推荐)
中标分类: H46
字数估计: 8,831
发布日期: 2017-09-07
实施日期: 2018-06-01
起草单位: 首钢总公司、冶金工业信息标准研究院、鞍钢股份有限公司
归口单位: 全国钢标准化技术委员会(SAC/TC 183)
提出机构: 中国钢铁工业协会
发布机构: 中华人民共和国国家质量监督检验检疫总局、中国国家标准化管理委员会
GB/T 20564.10-2017: 汽车用高强度冷连轧钢板及钢带 第10部分：孪晶诱导塑性钢
GB/T 20564.10-2017 英文名称: Continuously cold rolled high strength steel sheet and strip for automobile -- Part 10: Twinning induced plasticity steel
1 范围
GB/T 20564的本部分规定了冷轧孪晶诱导塑性高强度钢板及钢带的术语和定义、分类和牌号表
示方法、订货内容、尺寸、外形、重量、技术要求、试验方法、检验规则、包装、标志及质量证明书。
本部分适用于制造汽车复杂形状结构件、加强件等用厚度为0.50mm~3.00mm的钢板及钢带(以
下简称“钢板及钢带”)。
2 规范性引用文件
下列文件对于本文件的应用是必不可少的。凡是注日期的引用文件,仅注日期的版本适用于本文
件。凡是不注日期的引用文件,其最新版本(包括所有的修改单)适用于本文件。
GB/T 223.4 钢铁及合金 锰含量的测定 电位滴定或可视滴定法
GB/T 223.5 钢铁 酸溶硅和全硅含量的测定 还原型硅钼酸盐分光光度法
GB/T 223.9 钢铁及合金 铝含量的测定 铬天青S分光光度法
GB/T 223.59 钢铁及合金 磷含量的测定 铋磷钼蓝分光光度法和锑磷钼蓝分光光度法
GB/T 223.60 钢铁及合金化学分析方法 高氯酸脱水重量法测定硅含量
GB/T 223.68 钢铁及合金化学分析方法 管式炉内燃烧后碘酸钾滴定法测定硫含量
GB/T 223.71 钢铁及合金化学分析方法 管式炉内燃烧后重量法测定碳含量
GB/T 223.79 钢铁 多元素的测定 X-射线荧光光谱法
GB/T 228.1-2010 金属材料 拉伸试验 第1部分:室温试验方法
GB/T 247 钢板和钢带包装、标志及质量证明书的一般规定
GB/T 708 冷轧钢板和钢带的尺寸、外形、重量及允许偏差
GB/T 2523 冷轧金属薄板(带)表面粗糙度和峰值数测量方法
GB/T 2975 钢及钢产品 力学性能试验取样位置及试样制备
GB/T 4336 碳素钢和中低合金钢 多元素含量的测定 火花放电原子发射光谱法(常规法)
GB/T 8170 数值修约规则与极限数值的表示和判定
GB/T 17505 钢及钢产品 交货一般技术要求
GB/T 20066 钢和铁 化学成分测定用试样的取样和制样方法
GB/T 20123 钢铁 总碳硫含量的测定 高频感应炉燃烧后红外吸收法(常规方法)
GB/T 20125 低合金钢 多元素含量的测定 电感耦合等离子体原子发射光谱法
GB/T 20126 非合金钢 低碳含量的测定 第2部分:感应炉(经预加热)内燃烧后红外吸收法
3 术语和定义
下列术语和定义适用于本文件。
3.1
孪晶诱导塑性钢
通过高合金添加稳定奥氏体到室温,在塑性变形过程中单相奥氏体通过孪晶形成来延迟颈缩而获
得良好的塑性,同时奥氏体在高应变区会发生应变诱导马氏体相变,相变也延迟了颈缩的发生,从而提高塑性。
注:TWIP钢具有极高的强度塑性积,可以用于成形复杂的结构件或加强件。
4 分类和牌号表示方法
4.1 分类
4.1.1 钢板及钢带按表面质量分类见表1。
4.1.2 钢板及钢带按表面结构分类见表2。
4.2 牌号表示方法
钢板及钢带的牌号由冷轧英文“ColdRoled”首字母“CR”、规定最小屈服强度值/规定最小抗拉强
5 订货内容
5.1 按本部分订货的合同或订单应包括下列内容:
a) 产品名称(钢板或钢带);
b) 本部分编号;
c) 牌号;
d) 规格及尺寸、不平度精度;
e) 表面质量级别;
f) 表面结构;
g) 边缘状态;
h) 包装方式;
i) 重量;
j) 用途。
5.2 如订货合同中未注明尺寸和不平度精度、表面质量级别、表面结构种类、边缘状态及包装等信息,则本部分产品按普通的尺寸和不平度精度、较高级表面、表面结构为麻面、切边状态供货,并按供方提供的包装方式包装。
6 尺寸、外形、重量
钢板及钢带的尺寸、外形、重量及允许偏差应符合GB/T 708的规定。
7 技术要求
7.1 化学成分
钢的化学成分(熔炼分析)参考值参见附录A。如需方对化学成分有要求,应在订货时协商。
7.2 冶炼方法
钢板及钢带所用的钢采用氧气转炉或电炉冶炼,除非另有规定,冶炼方式由供方选择。
7.3 交货状态
7.3.1 钢板及钢带以退火后平整状态交货。
7.3.2 钢板及钢带通常涂油供货,所涂油膜应能用碱水溶液或通常的溶液去除,在通常的包装、运输、装卸及贮存条件下,供方应保证自制造完成之日起6个月内,钢板及钢带表面不生锈。如需方要求不涂油供货,应在订货时协商。
注:对于需方要求的不涂油产品,可能产生锈蚀,也可能在运输、装卸、储存和使用过程中表面易产生轻微划伤。
7.4 力学性能
钢板及钢带的力学性能应符合表3的规定。
试样为GB/T 228.1-2010中的P6试样(L0=80mm,b0=20mm),试样方向为纵向。
a 当屈服现象不明显时,可采用规定塑性延伸强度Rp0.2代替。
7.5 焊接
用户宜根据化学成分和强度级别确定合适的焊接工艺,必要时可咨询制造商。
7.6 表面质量
7.6.1 钢板及钢带表面不应有结疤、裂纹、夹杂等对使用有害的缺陷,钢板及钢带不应有分层。
7.6.2 钢板及钢带各表面质量应符合表4的规定。
7.6.3 对于钢带,由于没有机会切除有缺陷部分,因此允许带缺陷交货,但有缺陷部分应不超过每卷总长度的6%。
7.7 表面结构
钢板及钢带的表面结构应符合表5的规定。如需方对粗糙度有特殊要求,应在订货时协商。
8 试验方法
8.2 钢板及钢带的检验项目和试验方法应符合表6的规定。
9 检验规则
9.1 钢板及钢带的检查和验收由供方检验部门进行。
9.2 钢板及钢带应成批验收,每个检验批应由同一牌号、同一规格、同一加工状态的钢板或钢带组成。
每批的重量应不大于30t,对于卷重大于30t的钢带,每卷作为一个检验批。
9.3 钢板及钢带的取样数量和取样方法应符合表6的规定。
9.4 钢板及钢带的复验与判定规则应符合GB/T 17505的规定。
9.5 化学成分和力学性能的检测结果按修约值比较法进行修约,修约规则按GB/T 8170的规定。
10 包装、标志及质量证明书
订货时协商。
GB/T 20564.10-2017
GB
NATIONAL STANDARD OF THE
PEOPLE’S REPUBLIC OF CHINA
ICS 77.140.50
H 46
Continuously Cold Rolled High Strength
Steel Sheet and Strip for Automobile –
Part 10. Twinning Induced Plasticity Steel
ISSUED ON. SEPTEMBER 07, 2017
IMPLEMENTED ON. JUNE 01, 2018
Issued by. General Administration of Quality Supervision, Inspection and
Quarantine;
Standardization Administration of PRC.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative References ... 4
3 Terms and Definitions ... 6
4 Classification and Grade Expression Method ... 6
5 Ordering Content ... 7
6 Dimension, Shape, Weight ... 7
7 Technical Requirements ... 8
8 Test Method ... 9
9 Inspection Rules ... 10
10 Package, Mark and Quality Certificate ... 10
Appendix A (Informative) Chemical Compositions of Steel ... 11
Foreword
GB/T 20564 Continuously Cold Rolled High Strength Steel Sheet and Strip for
Automobile can be divided into the following 11 parts.
--- Part 1. Bake Hardening Steel;
--- Part 2. Dual Phase Steel;
--- Part 3. High Strength Interstitial Free Steel;
--- Part 4. High Strength Low Alloy Steel;
--- Part 5. Isotropic Steel;
--- Part 6. Transformation Induced Plasticity Steel;
--- Part 7. Martensitic Steel;
--- Part 8. Complex Phase Steel;
--- Part 9. Quenching and Partitioning Steel;
--- Part 10. Twinning Induced Plasticity Steel;
--- Part 11. Carbon Manganese Steel.
This Part belongs to Part 10 of GB/T 20564.
This Part was drafted as per the rules specified in GB/T 1.1-200.
This Part was proposed by China Iron and Steel Industry Association.
This Part shall be under the jurisdiction of National Technical Committee for
Standardization of Steels (SAC/TC 183).
Drafting organizations of this Part. Shougang Corporation, China Metallurgical
Information and Standardization Institute, and Angang Steel Company Limited.
Chief drafting staffs of this Part. Kuang Shuang, Liu Jun, Zhang Weixu, Guo Jinyu,
Tang Mu, Li Qian, Su Haolu, Shi Li, Lin Zhifeng, and Han Yun.
Continuously Cold Rolled High Strength
Steel Sheet and Strip for Automobile –
Part 10. Twinning Induced Plasticity Steel
1 Scope
This Part of GB/T 20564 specifies the terms and definitions, classification and grade
expression method, ordering content, dimension, shape, weight, technical
requirements, test methods, inspection rules, package, mark and quality certificate of
continuously cold rolled twinning induced plasticity high strength steel sheet and strip.
This Part is applicable to steel sheet and strip (hereinafter referred to as “steel sheet
and strip”) manufactured automotive complex structural parts, reinforcements, etc.,
with the thickness of 0.50mm~3.00mm.
2 Normative References
The following documents are essential to the application of this document. For the
dated documents, only the versions with the dates indicated are applicable to this
document; for the undated documents, only the latest version (including all the
amendments) are applicable to this document.
GB/T 223.4 Alloyed Steel - Determination of Manganese Content - Potentiometric
or Visual Titration Method
GB/T 223.5 Steel and Iron – Determination of Acid-Soluble Silicon and Total Silicon
Content - Reduced Molybdosilicate Spectrophotometric Method
Azurol S Photometric Method
GB/T 223.59 Iron, Steel and Alloy - Determination of Phosphorus Content -
Bismuth Phosphomolybdate Blue Spectrophotometric Method and Antimony
Phosphomolybdate Blue Spectrophotometric Method
GB/T 223.60 Methods for Chemical Analysis of Iron, Steel and Alloy - The
Perchloric Acid Dehydration Gravimetric Method for the Determination of Silicon
Content
GB/T 223.68 Methods for Chemical Analysis of Iron, Steel and Alloy - The
Potassium Iodate Titration Method after Combustion in the Pipe Furnace for the
GB/T 223.71 Methods for Chemical Analysis of Iron, Steel and Alloy the
Gravimetric Method after Combustion in the Pipe Furnace for the Determination
of Carbon Content
GB/T 223.79 Iron and Steel - Determination of Multi-Element Contents - X-Ray
Fluorescence Spectrometry
GB/T 228.1-2010 Metallic Materials - Tensile Testing - Part 1. Method of Test at
Room Temperature
GB/T 247 General Rule of Package, Mark and Certification for Steel Plates
(Sheets) and Strips
and Strip
GB/T 2523 Measuring Method of Surface Roughness and Peak Count for Cold-
Rolled Metal Sheet (Strip)
GB/T 2975 Steel and Steel Products - Location and Preparation of Test Pieces for
Mechanical Testing
GB/T 4336 Carbon and Low-Alloy Steel - Determination of Multi-Element Contents
-Spark Discharge Atomic Emission Spectrometric Method (Routine Method)
GB/T 8170 Rules of Rounding Off for Numerical Values & Expression and
Judgement of Limiting Values
GB/T 20066 Steel and Iron-Sampling and Preparation of Samples for the
Determination of Chemical Composition
GB/T 20123 Steel and Iron – Determination of Total Carbon and Sulfur Content
Infrared Absorption Method after Combustion in an Induction Furnace (Routine
Method)
GB/T 20125 Low-Alloy Steel - Determination of Multi-Element Contents -
Inductively Coupled Plasma Atomic Emission Spectrometric Method
GB/T 20126 Unalloyed Steel - Determination of Low Carbon Content - Part 2.
Infrared Absorption Method after Combustion in an Induction Furnace (with
400/950 – specified minimum yield strength value/specified minimum tensile strength value, in
MPa;
TW - characteristic letters of “Twinning induced plasticity”.
5 Ordering Content
5.1 The contract or ordering list that orders products as per this part include the
following contents.
a) Product name (steel sheet and strip);
b) This Part’s number;
c) Grade;
e) Surface quality levels;
f) Surface structure;
g) Edge state;
h) Packaging mode;
i) Weight;
j) Usage;
k) Other special requirements.
5.2 If the following information are not specified in the ordering contract, such as
dimension, roughness, surface quality level, surface structure type, edge state and
dimension, roughness accuracy, relative high surface, pitting surface structure, cutting
edge state, and packaged as per the packaging mode provided by the supplier.
6 Dimension, Shape, Weight
The dimension, shape, weight and allowable weight of steel sheet and strip shall
conform to the provisions of GB/T 708.
|