标准搜索结果: 'GB/T 33873-2017英文版'
标准号码 | 内文 | 价格(元) | 第2步 | 交付天数[PDF] | 标准名称 | 相关标准 |
GB/T 33873-2017 |
英文版
| 300 |
购买全文
|
现货, 9秒内下载
|
热老化试验箱能效测试方法
|
GBT 33873-2017
|
标准编号: GB/T 33873-2017 (GB/T33873-2017) 中文名称: 热老化试验箱能效测试方法 英文名称: Testing method of energy efficiency for hot aging test oven 行业: 国家标准 (推荐) 中标分类: F01 国际标准分类: 27.010 字数估计: 10,128 发布日期: 2017-07-12 实施日期: 2018-02-01 起草单位: 机械工业仪器仪表综合技术经济研究所、广东产品质量监督检验研究院、扬州光电产品检测中心、重庆四达试验设备有限公司、广州五所环境仪器有限公司、杭州雪中炭恒温技术有限公司、上海市计量测试技术研究院、成都易华天宇试验设备有限责任公司、上海爱斯佩克环境设备有限公司、深圳市标准技术研究院、无锡苏南试验设备有限公司、湖南省计量检测研究院、浙江省计量科学研究院、广州能源检测研究院、深圳国技仪器有限公司、珠海格力电器股份有限公司、中国计量大学 归口单位: 全国实验室仪器及设备标准化技术委员会(SAC/TC 526) 提出机构: 中国机械工业联合会 发布机构: 中华人民共和国国家质量监督检验检疫总局、中国国家标准化管理委员会
GB/T 33873-2017: 热老化试验箱能效测试方法
GB/T 33873-2017 英文名称: Testing method of energy efficiency for hot aging test oven
ICS 27.010
F01
中华人民共和国国家标准
热老化试验箱能效测试方法
中华人民共和国国家质量监督检验检疫总局
中国国家标准化管理委员会发布
前言
本标准按照GB/T 1.1-2009给出的规则起草。
本标准由中国机械工业联合会提出。
本标准由全国实验室仪器及设备标准化技术委员会(SAC/TC526)归口。
本标准起草单位:机械工业仪器仪表综合技术经济研究所、广东产品质量监督检验研究院、扬州光
电产品检测中心、重庆四达试验设备有限公司、广州五所环境仪器有限公司、杭州雪中炭恒温技术有限
公司、上海市计量测试技术研究院、成都易华天宇试验设备有限责任公司、上海爱斯佩克环境设备有限
公司、深圳市标准技术研究院、无锡苏南试验设备有限公司、湖南省计量检测研究院、浙江省计量科学研
究院、广州能源检测研究院、深圳国技仪器有限公司、珠海格力电器股份有限公司、中国计量大学。
本标准起草人:张桂玲、高晓东、魏玥峰、王成城、唐力华、李思远、陈锦汉、陈云生、谢晨浩、徐月明、
唐穗平、冯华、凌彦萃、黄强、王科、吴双双、万勇、周连琴、朱平、庞艳、陈帅、段华威、蒙家文、周四清、
黄宇、胡芬、陈其勇、胡晓峰、蒋建辉、谢小芳。
热老化试验箱能效测试方法
1 范围
本标准规定了热老化试验箱(以下简称为试验箱)能效测试的术语和定义、技术要求、测试条件、测
试方法等。
本标准适用于以电能为加热能源,以空气为传导介质的空气热老化试验箱、电热干燥箱及电热鼓风
干燥箱能效测试。
2 规范性引用文件
下列文件对于本文件的应用是必不可少的。凡是注日期的引用文件,仅注日期的版本适用于本文
件。凡是不注日期的引用文件,其最新版本(包括所有的修改单)适用于本文件。
GB/T 10592-2008 高低温试验箱技术条件
GB/T 30435-2013 电热干燥箱及电热鼓风干燥箱
JB/T 7444-1994 空气热老化试验箱
3 术语和定义
下列术语和定义适用于本文件。
4 产品技术要求
试验箱的性能要求应符合GB/T 30435-2013、JB/T 7444-1994的相关规定。
5 测试条件
5.1 环境条件
试验箱环境测试条件应满足:
a) 环境温度:23℃±2℃,环境温度测点处垂直方向的温度梯度不应超过2℃/m;
注:环境温度(试验箱周围的空间温度),即距试验箱边壁垂直中心线1m、距地面1m处的测试点测得的温度(环境
温度不应受到试验箱出气口温度的影响)。
b) 相对湿度:≤85%;
c) 气压:80kPa~106kPa;
d) 无强制对流空气。
5.2 电源条件
试验箱电源测试条件应满足:
a) 交流电压:220V±6.6V或380V±11.4V;
b) 频率:50Hz±0.5Hz。
5.3 测试设备
5.3.1 电能测量仪表
测量范围:电压、电流测量范围满足试验要求;
电能测量最大允许误差:不超过±0.5%;
用途:试验箱消耗有功电能测量。
5.3.2 功率表
测量范围:电压、电流测量范围满足试验要求;
功率测量最大允许误差:不超过±0.5%;
用途:试验箱消耗有功功率测量。
5.3.3 温度记录仪
温度测量范围:0℃~300℃;
最大允许误差:±0.5℃;
用途:试验箱几何中心温度测量。
5.3.4 秒表
日差的最大允许误差:±1s。
5.3.5 钢卷尺
准确度等级:Ⅱ级及以上;
用途:试验箱几何尺寸测量。
6 测试方法
6.1 试验箱工作状态
测试时试验箱应保持空载,并符合如下要求:
a) 预定与试验箱连接才能确保试验箱正常工作的附件,应按照使用说明书的安装要求完成安装
与连接;
b) 配置有测试孔的试验箱应采用附带的塞子保持测试孔密封;
c) 试验箱的门应保持完全关闭状态;
d) 将试验箱置于规定测试条件下预置至少2h,使试验箱内温度与环境温度一致;
e) 试验过程中,除换气量试验外,试验箱应设置为风门全闭状态。
6.2 工作空间的测量
采用尺等工具,将距离试验箱工作室壁为各自边长1/10的空间,分为若干易于测量的简单几何形
状进行测量,其结果即为试验箱工作空间,采用V 表示。
6.3 几何中心点温度的测量
注:几何中心点见GB/T 10592-2008中6.3.1。
6.4 试验箱试验温度
将试验箱温度设定为300℃。当箱体的最高温度达不到300℃时,试验箱测试温度设定为200℃,
但应在声明能效时标注测试温度。
6.5 恒温试验
设定试验箱几何中心点温度达到6.4的条件下,维持温度稳定2h,记录其中后1h的耗电量,用E1
表示。
6.6 变温试验
设定试验箱几何中心点温度达到55℃,维持温度稳定2h,再以最大温度变化速率升温到6.4的条
6.7 换气量试验
试验箱的换气量是衡量能耗的重要参数,换气量试验程序参照GB/T 7444-1994中的6.4.1,但试
验箱几何中心点的温度控制在75℃。
注:试验箱换气量测试结果的计算参照JB/T 7444-1994中的6.4.2。
GB/T 33873-2017
GB
NATIONAL STANDARD OF
THE PEOPLE’S REPUBLIC OF CHINA
ICS 27.010
F 01
Testing method of energy
Efficiency for hot aging test oven
ISSUED ON. JULY 12, 2017
IMPLEMENTED ON. FEBRUARY 1, 2018
Issued by. General Administration of Quality Supervision, Inspection
and Quarantine;
Standardization Administration Committee.
3. No action is required - Full-copy of this standard will be automatically &
immediately delivered to your EMAIL address in 0~60 minutes.
Table of Contents
Foreword ... 3
1 Scope ... 4
2 Normative references ... 4
3 Terms and definitions ... 4
4 Product technical requirements ... 5
5 Testing conditions ... 5
6 Measuring methods ... 7
7 Calculation method of energy efficiency ... 8
Foreword
This Standard was drafted in accordance with the rules given in GB/T
1.1-2009.
This Standard was proposed by China Machinery Industry Federation.
This Standard shall be under the jurisdiction of National Technical Committee
on Laboratory Instrument and Equipment of Standardization Administration of
China (SAC/TC 526).
The drafting organizations of this Standard. Machinery Industry
Instrumentation Technology and Economy Institute, Guangdong Institute of
Product Quality Supervision and Inspection, Yangzhou Optoelectronics
Products Testing Center, Chongqing Sida Test Equipment Co., Ltd.,
Guangzhou Wusuo Environmental Equipment Co., Ltd., Hangzhou Xuetemp
Technology Co., Ltd., Shanghai Institute of Measurement and Testing
Technology, Chengdu Yihua Tianyu Test Equipment Co., Ltd., Shanghai
Aisipeike Environmental Equipment Co., Ltd., Shenzhen Institute of
Standards and Technology, Wuxi Sunan Test Equipment Co., Ltd., Hunan
Institute of Measurement and Testing, Zhejiang Institute of Metrology,
Guangzhou Institute of Energy Testing, Shenzhen National Technology
Instrument Co., Ltd., Zhuhai Gree Electric Co., Ltd., China University of
Metrology.
Main drafters of this Standard. Zhang Guiling, Gao Xiaodong, Wei Yuefeng,
Wang Chengcheng, Tang Lihua, Li Siyuan, Chen Jinhan, Chen Yunsheng,
Xie Chenhao, Xu Yueming, Tang Suiping, Feng Hua, Ling Yancui, Huang
Qiang, Wang Ke, Wu Shuangshuang, Wan Yong, Zhou Lianqin, Zhu Ping,
Pang Yan, Chen Shuai, Duan Huawei, Meng Jiawen, Zhou Siqing, Huang Yu,
Hu Fen, Chen Qiyong, Hu Xiaofeng, Jiang Jianhui, Xie Xiaofang.
Testing method of energy
efficiency for hot aging test oven
1 Scope
This Standard specifies the terms and definitions, technical requirements,
testing conditions, testing methods for hot aging test oven (hereinafter
referred to as the test oven).
This Standard applies to energy efficiency test of air hot aging test oven,
gravity convection electric oven and forced ventilation electric oven that use
electric energy as heating energy, air as conduction medium.
2 Normative references
The following referenced documents are indispensable for the application of
this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including
any amendments) applies.
GB/T 10592-2008, Specification for low/high temperature test chambers
GB/T 30435-2013, Electric gravity convection and forced ventilation ovens
JB/T 7444-1994, Air heat-up ageing tests box
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1 hot aging test oven
3.2 gravity convection electric oven
a closed box obtaining the specified stable high temperature by electric
heating and with natural convection of air
3.3 forced ventilation electric oven
a closed box obtaining the specified stable high temperature by electric
The ambient conditions for the test oven shall meet the following.
a) ambient temperature. 23°C ± 2°C, the temperature gradient of ambient
temperature measuring point at the vertical direction shall not exceed
2°C/m;
the temperature measured at the measuring point, 1m from vertical central line of
the test oven wall, 1m from the ground (the ambient temperature is not affected by
the outlet temperature of the test oven).
b) relative humidity. ≤85%;
c) air pressure. 80kPa ~ 106kPa;
d) without forced convection air.
5.2 Power supply conditions
The power supply testing conditions for the test oven shall meet the following.
a) AC voltage. 220V ± 6.6V or 380V ± 11.4V;
5.3 Testing equipment
5.3.1 Energy measuring instrument
Measuring range. voltage, current measurement range shall meet the testing
requirements.
Maximum allowable energy measurement error. no more than ± 0.5%.
Usage. measurement of active energy consumption of the test oven.
5.3.2 Power meter
Measurement range. voltage, current measurement range shall meet the
testing requirements.
Usage. measurement of active power consumption of the test oven.
5.3.3 Temperature recorder
Temperature measurement range. 0°C ~ 300°C.
Maximum allowable error. ±0.5°C.
|